HOT
BRP BUDS / BUDS2 Kit – ATV & SSV
From $656.00
BRP BUDS / BUDS2 MPI-3 Diagnostic Kit 4-TEC/E-TEC/ACE
B.U.D.S. is comprehensive multi-language diagnostic software that gives you an insight on BRP® electronic modules. Along with this, you get all the manuals required for setting up the software and a hard copy of the software itself. However, keeping in mind the fact that the software is updated periodically from BRP itself, you will also be eligible to receive unlimited updates for the same through FTP. This is in addition to the license for the B.U.D.S. software so that you can operate it at your convenience without any problems.
For diagnosis of all BRP 4-TEC / E-TEC / ACE vehicles:
– all Can Am vehicles (ATV, SSV, Roadster Spyder).
- Description
- Additional information
- Diagnostic Kit includes:
- Minimum PC Requirements
Description
For diagnosis of all BRP 4-TEC / E-TEC / ACE vehicles:
– all Can Am vehicles (ATV, SSV, Roadster Spyder).
- CAN-AM ATV / SSV from 2004 till current (2025+)
Most useful functions:
- Reset TPS to zero position
- Read Fault Codes along with fault data
- Erase Fault Codes
- Reset Maintance Light
- Reset Service Hours
- Reset Service Rental Hours
- Change of owner’s information and the updating of purchase date.
- Combine Clusters to ECU’s
- Key programming (adding / removing / changing)
- Real Time Engine Monitor (Last 30 or 60 sec history, activate fuel pump, spark plugs, cluster WOW effect,…
| BRP BUDS Diagnostic kit – COMPARISON SHEET | ||
| BRP BUDS Diagnostic kit | ALL-DEALER / DEALER TECHNICIAN License | MEGATECH / MECHATRONIC EXPERT License |
| General Information | ||
| Change customer name | x | x |
| Reset Maintenance Warning | x | x |
| Reset trip hours | x | x |
| Reset Trip distance A | x | x |
| Reset Trip distance B | x | x |
| Change Model number | x | |
| Change Engine number | x | |
| Change VIN number | x | |
| Keys | ||
| Erase Key | x | x |
| Add Learning/Performance/Work key | x | x |
| Add Normal key | x | x |
| Enabling/Disabling DESS | x | |
| Installing Secure Code | x | |
| Change Key type without reprogramming key | x | |
| Settings | ||
| Throttle position sensor | x | x |
| Gear position sensor | x | x |
| Tire Size | x | x |
| ECM initialization | x | x |
| Change cluster language | x | x |
| Change cluster units | x | x |
| Change cluster mode (normal/racing) | x | x |
| Change Cluster Pointer Speed Position | x | x |
| Change Cluster Pointer RPM Position | x | x |
| Change Total Hours | x | |
| Setting Dynamic Power Steering (DPS) | x | x |
| Torque Adjustment | x | x |
| Change vehicle Configuration | x | |
| Enabling/disablingvehicle Option (DPS, Air Suspension, Belt protection, With fan, Electromechanical reverse, ) | x | |
| VCM Bleeding Front/Rear Circuit | x | x |
| VCM Reset Steering Angle Sensor | x | x |
| VCM Reset Yaw Rate Sensor | x | x |
| Edit curves for E-Tec Engines | x | |
| Monitoring | ||
| Engine speed | x | x |
| Engine RPM | x | x |
| Intake PSI | x | x |
| TPS | x | x |
| TAS | x | x |
| Gear position | x | x |
| Battery voltage | x | x |
| Engine temperature | x | x |
| GPS Position | x | x |
| iBR Gate position | x | x |
| iBR Target position | x | x |
| iBR BRLS Lever | x | x |
| Cylinder monitoring | x | x |
| Exhaust temperature | x | x |
| Oxygen Sensor Status | x | x |
| Low Oil Pressure | x | x |
| IACV Position | x | x |
| Fuel and Ignition | x | x |
| Atmospheric Pressure PSI | x | x |
| Intake Air | x | x |
| Engine Mode | x | x |
| Dynamic Power Steering | x | x |
| Cluster Lamp Activity | x | x |
| Cluster WOW | x | x |
| VCM Front / Rear Wheel Speed Sensor | x | x |
| VCM Lateral Acceleration | x | x |
| VCM Yaw Rate Sensor | x | x |
| VCM Steering Angle Sensor | x | x |
| ACS Position Sensor | x | x |
| ACS Switch Input | x | x |
| THCM Tuned Pipe | x | x |
| THCM Muffler | x | x |
| Activations | ||
| ECM Fuel Pressure Relief | x | x |
| ECM Fuel Pump | x | x |
| ECM Cooling Fan | x | x |
| ECM Battery Relay | x | x |
| ECM Oil System Bleeding | x | x |
| ECM Storage | x | x |
| Cluster WOW Test | x | x |
| Cluster Buzzer Test | x | x |
| Cluster Heater Handle | x | x |
| Cluster Heater Thumb | x | x |
| SCM Steering Assembly Validation | x | x |
| SCM Compressor | x | x |
| SCM Front / Rear Valve | x | x |
| SCM Shock Absorber Pressure (High Pressure) | x | x |
| SCM Auxiliary Line Pressure (Low Pressure) | x | x |
| iBR Position Test | x | x |
| IS Position Test | x | x |
| TCM Activation | x | x |
| TCM Gear Position | x | x |
| TCM Routine | x | x |
| ACC Suspension Up / Down | x | x |
| ACC Reverse Actuator | x | x |
| ACC Reverse Back Light | x | x |
| Faults | ||
| Summary (Code, State, Module, Count, Total Time, Description) | x | x |
| Clear Occurred Faults | x | x |
| All / Active / Occurred Faults | x | x |
| Possible Causes | x | x |
| Service Actions | x | x |
| Faults Conditions (Speed, TPS, Intake PSI, Engine temp, Battery, Engaged Gear,… | x | x |
| History | ||
| Min. / Max. (RPM, Intake PSI, Intake Temp,, Engine temp, Battery voltage) | x | x |
| Runtime in % (Normal / Limp Mode) | x | x |
| Runtime in Minutes (Normal / Limp Mode) | x | |
| RPM Profile in % | x | x |
| RPM Profile in Minutes | x | |
| Speed Profile in % | x | x |
| Speed Profile in Minutes | x | |
| Last Minute (RPM & Throttle Opening, Engine Temp, Intake Pressure, History Table) | x | x |
| Modules | ||
| ECM (Information & Update) | x | x |
| Cluster (Information & Update) | x | x |
| DPS (Information & Update) | x | x |
| IBR (Information & Update) | x | x |
| IBRMon (Information & Update) | x | x |
| IS (Information & Update) | x | x |
| VCM (Information & Update) | x | x |
| TCM (Information & Update) | x | x |
| IS (Information & Update) | x | x |
| THCM (Information & Update) | x | x |
| Clear History on Modules | x | |
| Cleaning Modules as New | x | |
| Advanced Functions in Modules | x | |
x – Supported
Additional information
| Weight | 10 lbs |
|---|---|
| ATV & SSV | 1 Year, 2 Years, 5 Years, 10 Years |
- BRP MPI-3 Interface (the main unit, is used for diagnosis of all BRP vehicles)
- Diagnostic Cable (for connection of MPI-3 Interface to 4-TEC / E-TEC / ACE vehicles
- USB Flash drive with software
- BRP Power interface unit (optional) ***
- BRP 4-Tec desspost unit (optional) ****
- BRP B.U.D.S. Diagnostic software (supports BRP vehicle till 2016)
- BRP B.U.D.S.2 Diagnostic software (supports BRP vehicle from 2016 and up) *
- Unlimited updates via the downloadable website,
- Access to the workshop (service manuals)
- User manual
- License for B.U.D.S. software
- License for B.U.D.S.2 Software *
- 24 MONTHS WARRANTY
- Intel i3, i5, i7 or AMD FX or Ryzen processor or better,
- Microsoft 64-bit Windows 7, Windows 8, Windows 10 or Windows 11,
- 6 Gb of RAM or more,
- 900 Mb of hard disk space (SSD drive will greatly improve loading time),
- VGA or higher resolution display (SVGA),
- Mouse or other pointing device,
- One unused USB port
Related products
BRP BUDS / BUDS2 Kit - DEALER TECH
From $702.00
PSFlasher - ECU Repair & Tuning Tool
From $234.00
BRP BUDS / BUDS2 Kit - Seadoo & Sportboat
From $656.00
